Aliased from Fire3

NanoPi Fire3 (click to enlarge)

The NanoPi Fire3 is a 7.5cm x 4cm Single Board Computer (SBC) which hosts a 1.4GHz Octa-Core Cortex-A53 with 1GB DDR3 RAM, with its CPU being a Samsung S56818 SoC. The Fire3 has a CMOS interface to support cameras, 40-Pin GPIO, MicroHDMI, RGB LCD Connector, and Gbps Ethernet.

It can run FriendlyCore, Debian, Android and Armbian.

Given it is only slightly larger than a Raspberry Pi Zero but hosts a 1.4GHz 8-core CPU, it's one of the more powerful small "Raspberry Pi compatible" SBCs available. As for true compatibility, see below.

The Fire3 has been tested by the NZPRG using the Armbian and Ubuntu operating systems. We recommend Armbian.

Note that when using Armbian, the armbian-config utility can be used to set most system configuration, including a static IP address.

Specifications#

NanoPi Fire3 (click to enlarge)

  • Octa-Core (i.e., 8 CPU cores) Cortex-A53 scaled up to 1.4GHz
  • SoC (CPU): Samsung S5P6818
  • Memory: 1GB DDR3 RAM
  • Dynamic Voltage Control
  • 1x MicroSD Slot
  • 1x Debug Serial Port / UART0
  • 1x USB 2.0 (Type-A)
  • 1x 1080P60 1.4A HDMI / Micro HDMI Type-D
  • 1x 0.54mm Pitch SMT FPC Seat that supports full-color (8-8-8) RGB LCD
  • 1x Micro USB to support data transmission and power input
  • 5mm Pitch FPC Socket supports DVP Camera (8-Bit ITU-R BT 601-658 / I/O, I2C included)
  • 54mm pitch Raspberry Pi compatible 40-Pin GPIO / PWM, I2C, UART, I/O, and SPI included
  • Power requirement: 5V/2A DC input power
  • Cortex-M0 MCU Power Management Unit supports Software Power-Off and RTC Alarm Power-On functions
  • Operating Temperature ranges from -20℃ to 70℃
  • Supports Armbian (Focal or Buster), Debian, Android 7.1.2, Ubuntu 16.04, FriendlyCore 16.04 (with Qt5.9 and OpenGL ES 1.1/2.0)
  • Supports Linux Kernel 4.4
  • 1x System LED
  • 1x Power Button
  • 1x Power indicator LED
  • 1x Reset Button
  • 1x RTC Battery Seat
  • passive heatsink included
  • Dimensions: 7.5cm x 4cm / 75mm x 40mm

Fire3 GPIO Pinout#

While it claims to be, the Fire3's GPIO is actually not compatible with the Raspberry Pi, notably the I2C bus is different.

Pin#NamePin#Name
1SYS_3.3V 2 VDD_5V
3 I2C0_SDA 4 VDD_5V
5 I2C0_SCL 6DGND
7GPIOD8/PPM8UART3_TXD/GPIOD21
9DGND10UART3_RXD/GPIOD17
11UART4_TX/GPIOB2912GPIOD1/PWM0
13GPIOB3014DGND
15GPIOB3116GPIOC14/PWM2
17SYS_3.3V 18GPIOB27
19SPI0_MOSI/GPIOC3120 DGND
21SPI0_MISO/GPIOD022UART4_RX/GPIOB28
23SPI0_CLK/GPIOC2924SPI0_CS/GPIOC30
25DGND26GPIOB26
27 I2C1_SDA 28 I2C1_SCL
29GPIOC830 DGND
31GPIOC732GPIOC28
33GPIOC13/PWM134DGND
35SPI2_MISO/GPIOC1136SPI2_CS/GPIOC10
37AliveGPIO338SPI2_MOSI/GPIOC12
39DGND40SPI2_CLK/GPIOC9

Tags:  Fire 3