Wiki: Ads 1015 Analog Digital Converter

ADS1015 Integrated Circuit (size: 2 x 1.5mm)

The Texas Instruments ADS1015 +/-24V Analog Digital Converter is a 2 x 1.5mm integrated circuit implemented by both AdaFruit and Pimoroni as I2C-compatible breakout boards (Pimoroni's is a "Breakout Garden" board). It can be used to measure an analog voltage between -24V DC to +24V DC, returning a value with 12 bit precision.

The ADS1015 has four channels (labeled A0, A1, A2 and A3) that can read voltages from -24V to +24V at sampling rates up to 3.3KHz with a 12-bit resolution. The Pimoroni board only provides three of these channels as usable pins.

ADS1015 Breakout Boards (click to enlarge)

The thumbnail image to the right is roughly the size of the Adafruit and Pimoroni boards, which measure 28 x 17mm and 24 x 21mm respectively. As of January 2020 the price of the AdaFruit board is US$9 (~NZ$14), the price of the Pimoroni board is £12 (~NZ$24). The Adafruit board is also available from DigiKey NZ at NZ$16.57 (where shipping is free if you order over NZ$66).

Features#

ADS1015 Block Diagram

12-bit precision
+/- 24V (DC) measurement range
three or four channels (the TI ADS1015 has four: AdaFruit's provides all four, whereas Pimoroni's board only provides connections to three of them)
programmable gain (please consult the ADS1015 TI datasheet for details; the default is set at ±2.048V)
pp to 3.3KHz sampling rate
I2C interface (address 0x48/0x49 (cut trace))
3.3V or 5V compatible
reverse polarity protection
compatible with all models of Raspberry Pi, and Arduino

Installation#

The Adafruit board has its own installation page (which we won't repeat here, see References below).

For the Pimoroni board, you'll need Python and pip (or pip3 for Python 3) already installed.

If you're using Python 2, just run:

sudo pip install ads1015

For Python 3, use:

sudo pip3 install ads1015

Example Usage#

The board has three input pins, labeled A0, A1 and A2. Plugging a signal into A0, here's an example of some code to repeatedly read the voltage on the pin until you type Ctrl-C:

    #!/usr/bin/env python3
    import time      
    from ads1015 import ADS1015
    
    print('''read-all.py - read the A0 input of the ADC.
    
    Press Ctrl+C to exit!
    ''')
     
    CHANNEL = 'in0/ref'
    ads1015 = ADS1015()
    ads1015.set_mode('single')
    ads1015.set_programmable_gain(2.048)
    ads1015.set_sample_rate(1600)
     
    reference = ads1015.get_reference_voltage()
    print("Reference voltage: {:6.3f}v \n".format(reference))
    
    try:
        while True:
            value = ads1015.get_compensated_voltage(channel=CHANNEL, reference_voltage=reference)
            print("A0 value: {:6.3f}v".format(value))
            time.sleep(0.5)
    
    except KeyboardInterrupt:
        pass

References#

ADS1015 12-Bit ADC - 4 Channel with Programmable Gain Amplifier Adafruit product page
- Adafruit 4-Channel ADC Breakouts: A guide to the ADS1115 and ADS1015 analog converters
ADS1015 +/-24V ADC breakout Pimoroni product page
- ads1015-python library on github
Adafruit ADS1015 product page on DigiKey
ADS101x Ultra-Small, Low-Power, I2C-Compatible, 3.3-kSPS, 12-Bit ADCs With Internal Reference, Oscillator, and Programmable Comparator datasheet from Texas Instruments

Tags: Sensor