The __SR04__ robot was designed and built by David P. Anderson.
It was David's fourth robot (hence the "04"), and was built sometime around 1998.
From David's description:
%%blockquote
__SR04__ is a small mobile robot suitable for exploring human habitats unattended.
It is controlled by a Motorola HC6811 microprocessor running in an M.I.T. 6.270 CPU card, similar to the commercially available "Handy Board." Two 12-volt DC gear-head motors maneuver the robot in a dual-differential drive configuration, balanced by a non-driven tail wheel caster and powered by a 12 volt 2.2 amp-hour sealed lead acid battery. Sensory input is provided by (in order of priority): front bumper switches, IR collision avoidance, stereo sonar ranging, photo detectors, passive IR motion detection, and shaft-encoder odometry.
%%
!! Design
%%small
~[The following includes text and images from David Anderson's web site; kindly used with permission.]
%%
[{Image src='attach/SR04/sr04-front-49-thumb.jpg' link='attach/SR04/sr04-front-49.jpg' caption='SR04 Front View' align='right' class='imgFloatRight' }]
%%hx Chassis %%
The design which has emerged is a small dual-differential drive platform with the geometry of an 11" circle. The drive wheels and tail caster sit on the perimeter of this circle, and thus it can rotate in its own space. This greatly simplifies software for maneuvering and collision avoidance.
%%hx CPU %%
The robot controller is a Motorola HC6811 microprocessor running in an M.I.T. 6.270 board. This card was developed for the introductory robotics course taught at M.I.T. It provides the HC6811 processor with 32k of battery-backed RAM, 32 eight-bit A/D channels, hardware 40khz IR , 6 one-amp H-Bridge (L293) motor driver channels, an LCD readout, and some digital I/O ports for timer and output compare functions useful to robot builder-types.
%%hx Software %%
The SR04 software exists as a collection of sensor routines and associated behaviors that are run concurrently by a round robn, non-preemptive multi-tasking scheduler. The structure is loosely based on Rodney Brooks' [subsumption architecture] as describe in Flynn's "Mobile Robots" book and more extensively on Brooks' home page (and elsewhere, run a web search on "subsumption").
Each sensor routine runs in turn in a 20 Hz sensor loop, and each sets a flag and some variables based on its own particular sensor input and state. An arbitration routine then picks the flag with the highest priority and passes it's variables along to the motor control sub-system. In this manner, sensors with higher priorities "subsume" the behaviors of lower priority sensors.
The priority scheme is based on the distance of the detecting event. Closer events have higher priority; more distant events have lower. The exact sequence is:
* __0__ User
* __1 __ Bumpers
* __2__ Rotation and Scanning
* __3__ IR Collision Avoidance
* __4__ Sonar Ranging
* __5__ Photo Approach/Avoid
* __6__ Motion Detector
* __7__ Dead-reckoning
Thus the Sonar ranging layer can subsume the Photo, Motion, and Dead-reckoning layers when it detects an obstacle or clear pathway. It is in turn subsumed by the IR collision avoidance, and the Rotation and Scanning behavior subsume both. The Bumper layer holds the ultimate control. All other tasks save the User (that's me) must give way if the robot has actually run into something, until the bumper behavior declares the robot to be free from obstructions. This formalization is an extremely useful way to organize multiple and potentially competing sensor inputs.
!! Subsystems
! A. PID Controller
A [Proportional Integral Derivative (PID) algorithm|PIDController] is used to control the main drive motors and maneuver the robot. This useful and subtle control method consists of three subsystems:
# __Shaft encoders__: Optical encoders attached directly to the motor shafts are used to accurately measure the speed of the motors (and by inference, the position of the robot).
# __Pulse Width Modulation__: Hardware timer interrupt generators in the HC6811 chip are used to generate two PWM sign \\ als that control the two L293 H-Bridges, which drive the main motors.
# __PID__: The PID algorithm itself runs in the 20 Hz sensor loop. It samples the shaft encoder variables to determine the current motor speeds, compares these to the requested motor speeds, and adjusts the PWM values up or down to get sampled and requested values to match.
The inputs to the PID control sub-system are the global variables, __velocity__, and __rotation__. Velocity is a signed value that represents the speed at the center of the robot, and rotation is a signed value that represents the difference in velocity between the two wheels. The PID controller reads these values, calculates the proper encoder counts per second for each wheel, and attempts to slew the motors toward the requested values, 20 times per second.
This method of closed loop control has a number of advantages. The velocity of the robot becomes independent of battery voltage, as the PID controller will increase the pulse width to make up for the sagging supply. It is also independent of load, so the robot can move very slowly and still climb over objects and maintain constant speed on an incline. The ability to control the wheels smoothly over a wide speed range translates into the ability to precisely maneuver the robot. The PID controller also provides stability for dead-reckoning algorithms.
! B. Odometry
The encoder counts returned from the [optical shaft encoders|MotorEncoder] mounted on the drive [motors] are also used to track the position of the robot relative to its position when last reset. These are maintained as a set of global variables that are updated at the 20 Hz sensor loop rate.
__X_position__ and __Y_position__ are the Cartesian co-ordinates in inches, and __Theta __is the rotation of the 'bot around its center in degrees. These data provide the "sensor input" for the dead-reckoning behaviors.
! C. Telemetry
A pair of "Lynx" radio tx/rcv modules is used to implement a telemetry back channel. The robot transmits a continuous stream of 80 character ASCII packets at 2400 baud. These consist of odometer and sensor data, battery voltage, state flags, and so forth. These are received and piped directly to the computer screen, or tee'd off to a file for later perusal. The transmitter on the robot draws only about 10 ma and is useful out to around 50 feet, depending on the space.
%%blockquote
Lately I have added a mode that allows the 'bot to wander freely about a space for three minutes, and then sound an alarm and try to dead-reckon back to the origin. This becomes very interesting if the path back to the origin has been blocked. I have seen the robot actually leave the room, go around the house, re-enter through a different doorway and finally back to the origin. — David Anderson
%%
%%small
~[Further descriptions of the SR04's sensors and behaviours are available from David Anderson's [SR04|http://www.geology.smu.edu/~dpa-www/robots/sr04/sr04.html] web page.]
%%
----
!! Links
* [SR04 Mobile Robot|http://www.geology.smu.edu/~dpa-www/robots/sr04/sr04.html], project description by David P. Anderson ([PDF version|http://www.cs.cmu.edu/~motionplanning/papers/sbp_papers/integrated2/anderson_sr04.pdf])
* [SR04 Mobile Robot|http://www.seattlerobotics.org/encoder/199806/sr04.htm] from the ''Newsletter of the Seattle Robotics Society''
* ''[Subsumption for hte SR04 and JBot Robots|http://www.dprg.org/articles/2007-03a/]'' \\
David P. Anderson, 26 March 2007